Simple push-fit straight barbed connectors to join two pieces of LeakyPipe, 16 / 20mm supply pipe polytube or hosepipe.  Useful for extending pipe or repairing damaged sections. No additional clips are required.

Packs include 5 fittings.

Available in 3 sizes:  Choose from the the selector above.

• 12mm - fits LeakyPipe LP12
• 16mm - fits 16mm polytube supply pipe, 1/2" hosepipe, and most other "Non-LeakyPipe®" porous rubber hoses.
• 20mm - fits 20mm polytube supply pipe

Joins LeakyPipe® to LeakyPipe® (LP12 range since 1987) to either extend the pipe, or areas of small damage can be cut out and the pipe repaired with these connectors.  Simply push the connector into the pipe.

A T-shaped connector for branching LeakyPipe, garden hosepipe or 16mm / 20mm supply pipe.

Each pack contains 5 fittings.

T-shaped connector to join 3 pieces of pipe of equal size, in effect 'branching'. A simple push-fit barbed fitting without the need for additional clips. Once connected, the pipe can be rotated on the fitting without breaking the seal. Choose required size as below.

• 12 - LeakyPipe LP12
• 16 - 16mm polytube or 1/2" garden hosepipe
• 20 - 20mm polytube

NB, reducing T connectors available for pipes of unequal size.  These T's can be very useful, depending on how you want to lay out your system.

Elbow-shaped connectors for LeakyPipe, garden hosepipe or 16 / 20mm polytube supply pipe.

A plastic elbow suitable for making tight corners with LeakyPipe. Simple push fit, no additional clips are needed. 

Available in 3 sizes

• 12mm - fits LeakyPipe® 
• 16mm - fits 16mm polytube and garden hosepipe
• 20mm - fits 20mm polytube

SOLD IN PACKS OF 5 CONNECTORS

End plugs to seal the ends of LeakyPipe, hosepipe and 16 / 20mm supply pipe. Simply push these fittings into the ends of your pipes to seal them off.

Push-fit, barbed plugs to seal the cut ends of your pipes.

SOLD IN PACKS OF 5 CONNECTORS!

Available in 3 sizes: 

12mm - fits LeakyPipe® LP12
16mm - fits 16mm polytube supply pipe or 1/2"hosepipe
20mm - fits 20mm polytube supply pipe

Connect LeakyPipe to non-porous supply pipe.

These simple push-fit connectors will join two unequal size pipes together.  Simply push together to connect the 2 pipes. No additional fittings or clips are needed.  

Available sizes include: 

• 16-12 - connect 1/2" hosepipe or 16mm polytube to LeakyPipe
• 20-12 - connect 20mm polytube to LeakyPipe
• 20-16 - connect 20mm polytube to 16mm polytube or 1/2" hosepipe

SOLD IN PACKS OF 5 CONNECTORS 

Connect LeakyPipe to garden hosepipe or 16mm or 20mm supply pipe. 

T-shaped connector to branch your water supply into LeakyPipe.

These connectors allow LeakyPipe to be connected to the larger non-porous pipes bringing water to your various beds and borders. The LeakyPipe can 'tee' into the side of larger supply pipes as they pass past the area you want to water.

Choose the connector you want above.  '12' fits LeakyPipe, '16' fits 1/2" garden hose or 16mm polytube and '20' fits 20mm polytube.  Simple push-fit barbs grip the inside of the pipe without the need for additional clips.

SOLD IN PACKS OF 5 CONNECTORS

• 16-12-16 - allows 1 LeakyPipe to tee connect into 16mm polytube
• 20-12-20 - allows 1 LeakyPipe to tee connect into 20mm polytube
• 20-16-20 - allows 16mm polytube to connect into 20mm polytube

Small selection pack of 12 connectors.
Connects LeakyPipe to 16mm or 20mm supply pipe or garden hose.

A selection pack of 12 barbed fittings which will enable a range of designs to be made up using LeakyPipe and 1/2" garden hose, 16mm or 20mm polytube supply pipe. This pack is suggested to be used with a 50m roll of LeakyPipe in terms of providing a good range and number of fittings that you may want for setting up an irrigation system.  If you have 100m roll of LeakyPipe, consider a large selection pack.

The small 12mm ends will fit LeakyPipe. The larger ends can either be size 16 (fits 1/2" garden hosepipe or 16mm supply pipe) OR size 20 (fits 20mm supply pipe). Make your selection above.

This Pack of Barbed Fittings Contains:

• Two  - large equal tee, (allows branching of supply pipe in T shape).
• Two  - large size to LeakyPipe reducing tee, (Leaky 'tee's' out of the side of supply pipe)
• Two - reducing straight connector, (supply pipe to Leaky)
• Two - 12-12-12 tee, (allows branching of LeakyPipe in T shape)
• Two - 12-12 straight connectors, (Leaky to Leaky repair connectors).
• Two - 12mm end plugs for sealing the LP ends.
  

Large selection pack of 30 connectors.
Connects LeakyPipe to 16mm or 20mm supply pipe or garden hose.

A selection of 30 barbed fittings which will enable a wide range of design layouts to be made up to suit your individual design needs, using LeakyPipe and 1/2" hosepipe, 16mm or 20mm polytube supply pipe. The small ends of the fittings connect to LeakyPipe (12mm). You can choose the larger size end: size 16 will fit 1/2" garden hosepipe or 16mm supply pipe, size 20 will fit 20mm supply pipe. 

This pack is suggested to be used with a 100m roll of LeakyPipe in terms of providing a good range and number of fittings that you may want for setting up an irrigation system. If you have 50m roll of LeakyPipe, consider a small selection pack. 

Pack contains:

• Three - Large Equal Size Tee, (size 16 or 20)
• Two - Large Equal Size Elbows (size 16 or 20)
• Six - Reducing Tee, (size 16/20 to Leaky)
• Five - Reducing Straight, (size 16/20 to Leaky)
• Five - Equal size 12-12-12 Tee. (for branching Leaky in T shape)
• Four - 12-12 straight connector, (Leaky to Leaky).
• Five - 12mm end plugs for sealing the LeakyPipe ends.

Tap for LeakyPipe® (12mm size)

A simple tap which allows isolation of areas from your irrigation system. Sold as a single unit.

These taps allow areas of your watering system to be switched on or off as required. 12mm size allows a section of LeakyPipe to be turned off e.g. a row on a vegetable patch 16mm or 20mm allow a whole section or your irrigation system to be shut down e.g. a particular border awaiting planting.

They have a barbed push-fit connection and clips are not needed.

Available in 3 sizes as shown:

• 12mm - fits LeakyPipe®
• 16mm - fits 16mm polytube or garden hosepipe
• 20mm - fits 20mm polytube

Please note these are NOT designed to hold back full (static) mains pressure.

Tap for 16mm supply pipe or garden hosepipe.

A simple tap which allows isolation of areas from your irrigation system. Sold as single unit.

Available in 3 sizes as shown:

• 12mm - fits LeakyPipe®
• 16mm - fits 16mm polytube or 1/2" garden hosepipe
• 20mm - fits 20mm polytube

These taps allow areas of your watering system to be switched on or off as required. 12mm size allows a section of LeakyPipe to be turned off e.g. a row on a vegetable patch. 16mm or 20mm allow a whole section or your irrigation system to be shut down e.g. a particular border awaiting planting. They have a barbed push-fit connection and clips are not needed. 

Please note these are NOT designed to hold back full (static) mains pressure.

Tap for 20mm supply pipe

A simple tap which allows isolation of areas from your irrigation system. Sold as single unit.

Available in 3 sizes as shown:

• 12mm - fits LeakyPipe®
• 16mm - fits 16mm polytube or garden hosepipe
• 20mm - fits 20mm polytube

These taps allow areas of your watering system to be switched on or off as required. 12mm size allows a section of LeakyPipe to be turned off e.g. a row on a vegetable patch. 16mm or 20mm allow a whole section or your irrigation system to be shut down e.g. a particular border awaiting planting. They have a barbed push-fit connection and clips are not needed. 

Please note these are NOT designed to hold back full (static) mains pressure

3/4" Male BSP threaded adaptor with barbed end to fit LeakyPipe® LP12 Porous Hose or garden hose or 16mm or 20mm polytube supply pipe.

A plastic adaptor with a 3/4" male thread converting to a barbed end of various sizes. Select the size you want above.

12mm - fits LeakyPipe® LP12 Porous Hose
16mm - fits garden hosepipe or 16mm supply polypipe
20mm - fits 20mm supply polypipe

SOLD IN PACKS OF 5 CONNECTORS

Pack of 9 fittings to bring water up and over the sides of existing raised beds, planters or troughs.

Pack of tee's and elbow's which brings water into an existing raised bed.

Simple push-fit connectors allow customisation around walls of different heights and widths.

A pack of push-fit connectors which allows creation of a non-leaking 'riser' to bring water up and over the sides of your existing raised beds. Once in the bed, the pipe size 'reduces' down to that of LeakyPipe. The LeakyPipe is laid amongst your plants on the surface of the soil or under a shallow layer of mulch/soil.  A LeakyPipe 'tee' permits branching of the LeakyPipe and 2 end plugs are also included. Lastly a nail-in pipe-clip keeps the supply pipe neat on top of the wall of your raised bed.

Choose either size 16mm or 20mm supply pipe. 16mm connectors will also fit 1/2" Garden Hosepipe. 

Fittings included:

• One Equal Tee (size 16/20) allows branching to the supply pipe to create a 'riser'
• Three Equal Elbows (size 16/20) allows the supply pipe to be fashioned neatly over the side of the raised bed 
• One supply pipe (size 16/20) -12 reducer, Reduces pipe size from supply size to LeakyPipe size.
• One 12-12-12 tee, (allows branching of LeakyPipe in T shape).
• Two 12 end plugs (for sealing the LeakyPipe ends).
• One nail-in pipe-clip (size compatible with your chosen supply pipe size)
  

Pack of compression fittings to create 'risers' to bring water up inside raised beds, planters, troughs or containers. Designed for use at the construction stage of building raised beds to create a neat look without pipes showing. Suitable for professional use in shared space communal areas or home domestic modern gardens. Compression fittings create reliable secure leak-free connections in areas that are difficult to access at a later date for maintenance. Compression fittings are compatible with blue 'mains' MDPE pipe or black LDPE pipe.

During construction, a 'riser' is created within the raised bed. At the soil surface, the compression elbow fitting will bring the pipe work level with the soil surface and allow connection to 2 lengths of LeakyPipe with simple push-fit barbed fittings. The LeakyPipe is laid amongst your plants on the surface of the soil or under a shallow layer of mulch/soil.  The LeakyPipe ends are sealed with the included plugs.  Overall this gives a neat look as the riser pipe and LeakyPipes will get covered by soil and not be visible.

Compression fittings are ideal for use in situations that would be difficult to access for maintenance at a later date.  These are great quality compression fittings and are the ones we choose to use ourselves, owing to their reliability.

Options include size 20mm or 25mm supply pipe.  Choose which size you would like and all connectors will automatically be swopped to your chosen size.

• One 20 or 25 compression Tee.  (allows branching to the supply pipe to create a 'riser')
• One 20 or 25 compression elbow to 12 barbed connector (allows connection to 2 lengths of LeakyPipe)
• Two 12 end plugs (for sealing the LeakyPipe ends).